Авторизация



Напомнить пароль
Регистрация

Штурм им. Conrad68078 / Advice On How To Work With A Fados9f1 Fault Detector

FADOS9F1 device ends in maximization current and also produces supply graph from the defective card. This card is erect to be drawn maximization amount of current. Then IR sensor is measured from included material temperature. It can be used in some kind of specific material current it can be drawn further much or less current. In this way, the open circuit the defective card to draw less current. In the following cases of the FADOS9F1 device can be initiated from oscilloscope screen and found to the broken connection of the power supply line.

This new technique deals with high voltage that makes to adjust power cable connection in the input of intact board. This method is specifically developed for the power test button and it gives exact output voltage between 0 and 100 mV. This output is to get and draw a graph as the mandatory process. A voltage graph result will take after some minutes f or the temperature map. It assists to the IR sensor for the usage of calculating another component of temperature. Mainly, defected circuit board needs to test the intact card graph.

There is no difference from the testing device, which comes with the audio, video, medical sector, motor control, automotive sector and mobile phone or some other developing areas are used only electronic components. A fados9f1 tester can help with reliability and troubleshooting of electronic circuit without making any applying power to UUT. This system makes to avoid high risk and the process leads to the consequential damage. Finally, there is no any occurrence for defective components or low impedance connection as well as a short circuit.

Again FADOS9F1 provides two additional features like noncontact IR temperature measurement and programmable power supply when compared to FADOS7F1. The first one is programmable DC power supply that involv es this product, which will connect to the power line of UUT and set maximum voltage. Now the test button is activated, device software will produce to give voltage output of 100mV. The current value and voltage va lue is to be saved in your file. After few minutes, measurement of temperature will be done as a process to use high-temperature component and another related defect component.

FADOS9F1 is nothing but Fault Detector and Oscilloscope which consists of nine functions in a single device. It is also a computer-based voltage-current tester as well as VI C urve T ester. Normally it is recommended to use in large and medium laboratories to get an output of greater efficiency. The device is made to be developed as a V/I tester from ProT Ar-Ge which is the Industrial Project Design of L it is used to find the components to generate the high temperature. Above features are included in that device and it has to decrease huge amount time of troubleshooting to blemish at five to ten minutes. The IR temperature measurement sensor is a new troubleshooting technique.

Even though FADOS9F1 is very small in size, but this device is easy to carry out even you will take out in a briefcase. Ecu fados tester is another type of tester and its make your work very simple and easy. Another usage area of a FADOS9F1 device such as medical devices circuit, servo step motor drivers, the circuit board of monitor and computer, ECU automotive electronic circuit boards, radio and audio, television circuit board, the textile machine of circuit board, electronic circuit board of mobile phones, electronic circuit board of military and much more. The FADOS9F1 device is used to be testing only electronic components such as capacitors, transistors, resistors, diode, inductors, integrated circuits, optocouplers, SCR�s, TRIAC�s and many more electronic components.

Through this technique, you can find the broken line easily. Then the power graph is made to be produced for the defective boards. If the power graph of the intact board will be equal to the power graph of the defective board, then it is the time to activate the VI tester to identify the malfunction occurred on the board. This FADOS9F1 is also utilized in Microvolt measurements and it also offers an output port for the purpose of attaching multiplexer. The product s of FADOS are made to be designed to perform multiple functions to meet all the situations that are encountered by the customer.

This technique is also dealt with the maximum voltage is made to be adjusting with the connection of power cable in the intact board input. Normally, This adjustment method is developed by the �Power Test� button, which provides desired result from 0 to 100mV voltage. The desired result is obtained to draw the graph and get the record if necessary. After few minutes, the desired result of voltage graph provides temperature map, which helps to IR sensor. Then the IR sensor is also used to calculate some other component temperature. An intact card graph is required to be testing only defected circuit board.

There are nine functions in this device. They are Analog Voltage Output, Measuring Equipment for Capacitor, Fault Detection by Comparison from memory, DC Power Supply Output developed with adjustable voltage and current, Diode and Resistor, Equivalent Circuit diagram, Double Channel just click the up coming internet site Detection, Double Channel Digital PC Oscilloscope, Square Wave Signal Output between 0.2 kHz and 25 kHz and Non Touched IR Temperature Sensor. The common features are to be analyzed from VI Curve and it's also very difficult to search some other product.

Вставка изображения

Комментарии (0)

RSS свернуть / развернуть

Автор топика запретил добавлять комментарии